[ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Linux version 2.6.31.14.22 (sepen@ekopark) (gcc version 4.5.2 (GCC) ) #3 PREEMPT Tue Jul 19 23:42:53 UTC 2011 [ 0.000000] CPU: ARMv7 Processor [412fc085] revision 5 (ARMv7), cr=10c53c7f [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache [ 0.000000] Machine: Genesi Efika MX (Smarttop) [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] On node 0 totalpages: 106496 [ 0.000000] free_area_init_node: node 0, pgdat 8073d5e0, node_mem_map 80790000 [ 0.000000] DMA zone: 192 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 24384 pages, LIFO batch:3 [ 0.000000] Normal zone: 640 pages used for memmap [ 0.000000] Normal zone: 81280 pages, LIFO batch:15 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 105664 [ 0.000000] Kernel command line: console=ttymxc0,115200 root=/dev/sda1 rootwait ro [ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 416MB = 416MB total [ 0.000000] Memory: 414336KB available (6528K code, 588K data, 160K init, 0K highmem) [ 0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:368 [ 0.000000] MXC IRQ initialized [ 0.000000] MXC_Early serial console at MMIO 0x73fbc000 (options '115200') [ 0.000000] console [ttymxc0] enabled [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Calibrating delay loop... 799.53 BogoMIPS (lpj=3997696) [ 0.000000] Mount-cache hash table entries: 512 [ 0.000000] Initializing cgroup subsys ns [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Initializing cgroup subsys freezer [ 0.000000] Initializing cgroup subsys net_cls [ 0.000000] CPU: Testing write buffer coherency: ok [ 0.000000] devtmpfs: initialized [ 0.000000] regulator: core version 0.5 [ 0.000000] NET: Registered protocol family 16 [ 0.000000] i.MX IRAM pool: 128 KB@0x9a840000 [ 0.000000] IRAM READY [ 0.000000] CPU is i.MX51 Revision 3.0 [ 0.000000] MXC GPIO hardware [ 0.000000] Efika MX: mmc0 configured as external SDHC [ 0.000000] Efika MX: Smarttop Revision 1.3 [ 0.000000] Using SDMA I.API [ 0.000000] MXC DMA API initialized [ 0.000000] bio: create slab at 0 [ 0.000000] SCSI subsystem initialized [ 0.000000] libata version 3.00 loaded. [ 0.000000] CSPI: mxc_spi-0 probed [ 0.000000] usbcore: registered new interface driver usbfs [ 0.000000] usbcore: registered new interface driver hub [ 0.000000] usbcore: registered new device driver usb [ 0.000000] IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7) [ 0.000000] NET: Registered protocol family 8 [ 0.000000] NET: Registered protocol family 20 [ 0.000000] mc13892 Rev 2.0 FinVer 2 detected [ 0.000000] Initializing regulators for Efika MX [ 0.000000] regulator: SW1: 600 <--> 1375 mV [ 0.000000] regulator: SW2: 900 <--> 1850 mV [ 0.000000] regulator: SW3: 1100 <--> 1850 mV [ 0.000000] regulator: SW4: 1100 <--> 1850 mV [ 0.000000] regulator: SWBST: 0 mV [ 0.000000] regulator: VIOHI: 0 mV [ 0.000000] regulator: VPLL: 1050 <--> 1800 mV [ 0.000000] regulator: VDIG: 1650 mV [ 0.000000] regulator: VSD: 1800 <--> 3150 mV [ 0.000000] regulator: VUSB2: 2400 <--> 2775 mV [ 0.000000] regulator: VVIDEO: 2775 mV [ 0.000000] regulator: VAUDIO: 2300 <--> 3000 mV [ 0.000000] regulator: VCAM: 2500 <--> 3000 mV fast normal [ 0.000000] regulator: VGEN1: 1200 <--> 3150 mV [ 0.000000] regulator: VGEN2: 1200 <--> 3150 mV [ 0.000000] regulator: VGEN3: 1800 <--> 2900 mV [ 0.000000] regulator: VUSB: 0 mV [ 0.000000] regulator: GPO1: 0 mV [ 0.000000] regulator: GPO2: 0 mV [ 0.000000] regulator: GPO3: 0 mV [ 0.000000] regulator: GPO4: 0 mV [ 0.000000] Device spi1.0 probed [ 0.000000] NET: Registered protocol family 2 [ 0.000000] IP route cache hash table entries: 4096 (order: 2, 16384 bytes) [ 1.349099] Switched to high resolution mode on CPU 0 [ 1.350267] TCP established hash table entries: 16384 (order: 5, 131072 bytes) [ 1.358046] TCP bind hash table entries: 16384 (order: 4, 65536 bytes) [ 1.364890] TCP: Hash tables configured (established 16384 bind 16384) [ 1.371448] TCP reno registered [ 1.374829] NET: Registered protocol family 1 [ 1.379679] LPMode driver module loaded [ 1.383525] Static Power Management for Freescale i.MX51 [ 1.388993] PM driver module loaded [ 1.392642] sdram autogating driver module loaded [ 1.397551] Bus freq driver module loaded [ 1.401624] mxc_dvfs_core_probe [ 1.404914] DVFS driver module loaded [ 1.408593] i.MXC CPU frequency driver [ 1.412568] DVFS PER driver module loaded [ 1.426549] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.434489] Registering unionfs 2.5.7 (for 2.6.31.14) [ 1.441041] JFFS2 version 2.2. (NAND) \xffffffc2\xffffffa9 2001-2006 Red Hat, Inc. [ 1.448550] JFS: nTxBlock = 3238, nTxLock = 25908 [ 1.454919] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled [ 1.466010] Btrfs loaded [ 1.468570] msgmni has been set to 809 [ 1.479512] alg: No test for stdrng (krng) [ 1.483741] alg: No test for stdrng (ansi_cprng) [ 1.488566] cryptodev: driver loaded. [ 1.492525] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 1.499973] io scheduler noop registered (default) [ 1.505026] io scheduler cfq registered [ 1.510502] mxc_ipu mxc_ipu: Channel already disabled 9 [ 1.510516] mxc_ipu mxc_ipu: Channel already uninitialized 9 [ 1.510555] mxc_sdc_fb mxc_sdc_fb.0: mxcfb: Error initializing panel. [ 1.513622] Console: switching to colour frame buffer device 80x30 [ 2.180007] SIIHDMI: Device ID: 0xb0 (TPI revision 2.9) [ 2.188139] SIIHDMI: no sink detected, ,  [ 2.188539] SIIHDMI: unable to change to a low power-state [ 2.201738] Serial: MXC Internal UART driver [ 2.206199] mxcintuart.0: ttymxc0 at MMIO 0x73fbc000 (irq = 31) is a Freescale i.MX [ 2.213944] console handover: boot [ttymxc0] -> real [ttymxc0] [ 2.224540] brd: module loaded [ 2.230153] loop: module loaded [ 2.234821] pata_fsl pata_fsl: rchan=29 wchan=28 [ 2.239686] scsi0 : pata_fsl [ 2.242936] ata1: PATA max UDMA/44 irq 70 [ 2.247574] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.359103] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller [ 2.365983] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1 [ 2.399121] fsl-ehci fsl-ehci.0: irq 18, io base 0x73f80000 [ 2.419091] fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00 [ 2.424769] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.431592] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.438822] usb usb1: Product: Freescale On-Chip EHCI Host Controller [ 2.445286] usb usb1: Manufacturer: Linux 2.6.31.14.22 ehci_hcd [ 2.451227] usb usb1: SerialNumber: fsl-ehci.0 [ 2.456044] usb usb1: configuration #1 chosen from 1 choice [ 2.461800] hub 1-0:1.0: USB hub found [ 2.465615] hub 1-0:1.0: 1 port detected [ 2.473740] ata1.00: ATA-8: SanDisk pSSD-P2 8GB, SSD 5.20, max UDMA/133 [ 2.480402] ata1.00: 15649200 sectors, multi 0: LBA48 [ 2.524809] ata1.00: configured for UDMA/44 [ 2.539455] scsi 0:0:0:0: Direct-Access ATA SanDisk pSSD-P2 SSD PQ: 0 ANSI: 5 [ 2.548223] sd 0:0:0:0: [sda] 15649200 512-byte logical blocks: (8.01 GB/7.46 GiB) [ 2.556116] sd 0:0:0:0: [sda] Write Protect is off [ 2.561254] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 2.566774] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 2.566956] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.576921] sda: sda1 sda2 sda3 sda4 [ 2.583050] sd 0:0:0:0: [sda] Attached SCSI disk [ 2.689108] usb 1-1: new high speed USB device using fsl-ehci and address 2 [ 2.696286] fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller [ 2.703218] fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2 [ 2.739124] fsl-ehci fsl-ehci.1: irq 14, io base 0x73f80200 [ 2.849088] fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00 [ 2.854740] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.861560] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.868790] usb usb2: Product: Freescale On-Chip EHCI Host Controller [ 2.875253] usb usb2: Manufacturer: Linux 2.6.31.14.22 ehci_hcd [ 2.881193] usb usb2: SerialNumber: fsl-ehci.1 [ 2.885996] usb usb2: configuration #1 chosen from 1 choice [ 2.891751] hub 2-0:1.0: USB hub found [ 2.895563] hub 2-0:1.0: 1 port detected [ 2.899744] Initializing USB Mass Storage driver... [ 2.904770] usbcore: registered new interface driver usb-storage [ 2.910826] USB Mass Storage support registered. [ 2.915511] usbcore: registered new interface driver ums-cypress [ 2.921730] usbcore: registered new interface driver usbserial [ 2.927618] USB Serial support registered for generic [ 2.946488] usb 1-1: New USB device found, idVendor=0b95, idProduct=772a [ 2.953222] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 2.960393] usb 1-1: Product: AX88x72A [ 2.964146] usb 1-1: Manufacturer: ASIX Elec. Corp. [ 2.969027] usb 1-1: SerialNumber: 123456 [ 2.973384] usb 1-1: configuration #1 chosen from 1 choice [ 2.980540] usbcore: registered new interface driver usbserial_generic [ 2.987076] usbserial: USB Serial Driver core [ 2.991665] mice: PS/2 mouse device common for all mice [ 2.996980] mc13892 rtc probe start [ 3.009360] pmic_rtc pmic_rtc.1: rtc core: registered pmic_rtc as rtc0 [ 3.015895] mc13892 rtc probe succeed [ 3.019637] i2c /dev entries driver [ 3.023371] Linux video capture interface: v2.00 [ 3.028238] mxc_v4l2_output mxc_v4l2_output.0: Registered device video0 [ 3.034964] MXC WatchDog Driver 2.0 [ 3.038563] clk: Unable to get requested clock: wdog_clk [ 3.044055] MXC Watchdog # 0 Timer: initial timeout 60 sec [ 3.050657] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com [ 3.059214] cpuidle: using governor ladder [ 3.063316] cpuidle: using governor menu [ 3.067430] PMIC Character device: successfully loaded [ 3.072765] SCC2: Driver Status is OK [ 3.076530] Sahara HW Version is 0x27000410 [ 3.080795] ioctl pointer: 8043b6a4. mmap pointer: 8043b008 [ 3.088669] In fsh_shw_smalloc (km): partition_base:9ac5c000 partition_base_phys: 1fffc000 [ 3.096969] writing UMID and MAP to secure the partition [ 3.102841] VPU initialized [ 3.237019] mxsdhci: MXC Secure Digital Host Controller Interface driver [ 3.243806] mxsdhci: MXC SDHCI Controller Driver. [ 3.248936] mmc0: SDHCI detect irq 128 irq 1 INTERNAL DMA [ 3.254686] Registered led device: efikamx:green [ 3.259494] Registered led device: efikamx:red [ 3.264087] Registered led device: efikamx:blue [ 3.269288] Advanced Linux Sound Architecture Driver Version 1.0.20. [ 3.277432] ALSA device list: [ 3.280465] No soundcards found. [ 3.285529] TCP cubic registered [ 3.288768] NET: Registered protocol family 17 [ 3.304130] RPC: Registered udp transport module. [ 3.308845] RPC: Registered tcp transport module. [ 3.313726] ThumbEE CPU extension supported. [ 3.318478] input: Efika MX Input as /devices/virtual/input/input0 [ 3.325036] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2 [ 3.333219] regulator_init_complete: incomplete constraints, leaving GPO4 on [ 3.340312] regulator_init_complete: incomplete constraints, leaving GPO3 on [ 3.347368] regulator_init_complete: incomplete constraints, leaving GPO2 on [ 3.354444] regulator_init_complete: incomplete constraints, leaving GPO1 on [ 3.361518] regulator_init_complete: incomplete constraints, leaving VGEN1 on [ 3.368660] regulator_init_complete: incomplete constraints, leaving VCAM on [ 3.375729] regulator_init_complete: incomplete constraints, leaving VAUDIO on [ 3.382974] regulator_init_complete: incomplete constraints, leaving VSD on [ 3.389957] regulator_init_complete: incomplete constraints, leaving VDIG on [ 3.397014] regulator_init_complete: incomplete constraints, leaving SWBST on [ 3.404316] usb 2-1: new high speed USB device using fsl-ehci and address 2 [ 3.442564] VFS: Mounted root (ext2 filesystem) readonly on device 8:1. [ 3.451368] devtmpfs: mounted [ 3.454494] Freeing init memory: 160K [ 3.570129] usb 2-1: New USB device found, idVendor=1a40, idProduct=0101 [ 3.576924] usb 2-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 3.584161] usb 2-1: Product: USB 2.0 Hub [MTT] [ 3.589193] usb 2-1: configuration #1 chosen from 1 choice [ 3.595255] hub 2-1:1.0: USB hub found [ 3.599551] hub 2-1:1.0: 4 ports detected [ 3.879499] usb 2-1.1: new high speed USB device using fsl-ehci and address 3 [ 4.007407] usb 2-1.1: New USB device found, idVendor=13d3, idProduct=3273 [ 4.014359] usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 4.021739] usb 2-1.1: Product: 802.11 n WLAN [ 4.026100] usb 2-1.1: Manufacturer: Ralink [ 4.030305] usb 2-1.1: SerialNumber: 1.0 [ 4.034692] usb 2-1.1: configuration #1 chosen from 1 choice [ 4.043361] <30>udev[65]: starting version 167 [ 4.179474] rt2870sta: module is from the staging directory, the quality is unknown, you have been warned. [ 4.221588] rtusb init ---> [ 4.233203] usbcore: registered new interface driver rt2870 [ 4.568271] sgtl5000-i2c 1-000a: SGTL5000 revision 17 [ 5.793245] eth0: register 'asix' at usb-fsl-ehci.0-1, ASIX AX88772 USB 2.0 Ethernet, 70:71:bc:5f:b8:d8 [ 5.802850] usbcore: registered new interface driver asix [ 6.409599] Adding 524280k swap on /var/swap. Priority:-1 extents:401 across:1502332k SS